|
Friday, May 2, 2008 - 12:41AM 
|
Lightning video problems with HD cameras
The proliferation of HD video cameras into the world of storm video has had many chasers scratching their heads when it comes to lightning video. Why do many of today's HD camera offerings have so much trouble with lightning? There are several causes, each with their own unique symptoms. The following are the three common types of lightning artifacting encountered with HD video:
1.) CMOS Rolling Shutter
Most cameras manufactured up until a few years ago used CCD imaging sensors. These sensors capture all of their pixels simultaneously for each video frame, meaning that the entire image is captured at once. A lightning bolt then would be captured in its entirety on a CCD, even if it occupied only a single video frame in time.
By contrast, a CMOS chip captures its images differently, using a rapid top-to-bottom scan of the sensor. You can picture this process as using a small paintbrush to paint a wall, using single horizontal strokes across it and working your way downward. If an instantaneous change in brightness of the scene happens in the middle of a CMOS chip scan (as with a lightning flash), the result is a 'split screen' with part of the frame light and the other dark.
The following are frame captures of lightning from a CMOS-chip based camcorder that show the rolling shutter problem:
In the last example, you can see that two rapid brightness changes occured during a single frame scan of the sensor, resulting in two 'splits' of the frame.
Unfortunately for storm chasers, the trend is that CCD chips are being widely phased out in favor of CMOS in nearly all new HD video cameras (both consumer AND prosumer models). CMOS chips are cheaper, use less power and capture better images in well-let scenes than CCDs. While some of the CMOS cameras can perform well with lightning in certain environments, the majority of their lightning video will exhibit the rolling shutter problem. If the camera has a CMOS chip - no matter how expensive it is (including the new Sony XDCAM EX1) - it will have this problem with capturing lightning.
A good test to check a camera for rolling shutter is using a camera flash in a darkened room, which will produce the same 'split screen' effect as a lightning flash.
2.) HDV Compression
The second type of artifacting that chasers may see on HD lightning footage has to do with the limitations of the 25Mbps HDV codec. When a video scene changes quickly from frame to frame, the MPEG compression has a hard time keeping up - and artifacting will result in the form of blocky pixelation. When a lightning flash happens, the entire scene will change from dark to light and dark again, often in single-frame increments. This rapid change overloads the compression codec, resulting in artifacts. It is more pronounced at night, when lightning will result in a large degree of change in the brightness of the scene. The compression artifacts are nearly non-existent in daytime lightning video, as the entire scene usually will not be illuminated by a flash.
Most HDV artifacting with lightning is usually hard to see without scrutinizing the footage closely on a large monitor/TV, or by extracting still frames. Some examples, however, are worse than others.
The following video frame shows a more severe case of HDV compression artifacting from a nighttime lightning strike:
Zooming in on the frame shows what the artifacts look like up close:
A CMOS-based camera that uses HDV may exhibit both rolling shutter AND the compression artifacting.
3.) Interlacing in encoded video files
The third common problem with lightning footage comes after the video has been imported into editing software and encoded into a file for the web (such as a Windows Media, FLV or Quicktime file). Exported video files may exhibit numerous horizontal lines whenever a lightning flash happens. Fortunately, this issue doesn't indicate any problem with the source video itself, but rather a setting in the video encoding process. This artifact happens because the interlacing in the source footage is being 'resized' into the smaller web video. The following is an example of this:
To correct this problem, you must apply deinterlacing to each lightning clip prior to exporting an encoded video. In Adobe Premiere, this is accomplished by right-clicking on each clip in the timeline and choosing 'Field Options', then 'Always Deinterlace':
 | Hi Dan, hows the Guide service going, had any interested people ? like you said before might be a bit late for this season on the plains. Deff push it all through next winter.
- Posted by Mick from United Kingdom | |  | |
Nothing so far. Google's being weird on the placement of the site - three days ago I was on the first page for chase tour queries, today I'm nowhere to be seen. Just got my IRS payout today, which will cover gas money to and from the Plains once. So even if I'm too late on the tours, I may get one trip in out west. Just waiting on a good multi-day setup out there.
- Posted by Dan R. from Charleston, WV | | | |
Good at least it looks you can asure yourself of one good trip this season, will keep watching !!
- Posted by Mick from United Kingdom | | | |
|
